Techniques for WCAG 2.0

Skip to Content (Press Enter)

This document is a draft, and is designed to show changes from a previous version. It is presently showing added text,changed text,deleted text,[start]/[end] markers,and Issue Numbers.

Hide All Edits   |   Toggle Deletions  |   Toggle Issue Numbers   |   Toggle [start]/[end] Markers   |   Show All Edits

Changes are displayed as follows:

-

G18: Ensuring that a contrast ratio of at least 4.5:1 exists between text (and images of text) and background behind the text

Applicability

Any technology that produces visual output.

This technique relates to:

Description

The objective of this technique is to make sure that users can read text that is presented over a background. For Success Criterion 1.4.3, this technique describes the minimum contrast ratio for text that is less than 18 point (if not bold) and less than 14 point (if bold). For Success Criterion 1.4.5, this technique relaxes the 7:1 contrast ratio requirement for text that is at least 18 point (if not bold) or at least 14 point (if bold).

If the background is a solid color (or all black or all white) then the relative luminance of the text can be maintained by making sure that each of the text letters have 4.5:1 contrast ratio with the background.

If the background or the letters vary in relative luminance (or are patterned) then the background around the letters can be chosen or shaded so that the letters maintain a 4.5:1 contrast ratio with the background behind them even if they do not have that contrast ratio with the entire background.

[begin add]

For example, if a letter is lighter at the top than it is a the bottom, it may be difficult to maintain the contrast ratio between the letter and the background over the full letter. In this case, the designer might darken the background behind the letter, or a thin black outline (at least one pixel wide) around the letter in order to keep the contrast ratio between the letter and the background above 4.5:1.

[end add]

The contrast ratio can sometimes be maintained by changing the relative luminance of the letters as the relative luminance of the background changes across the page.

[begin add]

For example, if a page is very light on one edge and fades to very dark on the other edge, there is no color that can run across the page and meet the contrast guidelines on both edges. One way of addressing this would be to change the lightness of the letters as well so that each letter always meets the contrast ratio for the background that is immediately behind the letter.

[end add]

Another method is to provide a halo around the text that provides the necessary contrast ratio if the background image or color would not normally be sufficiently different in relative luminance.

Examples

Resources

Resources are for information purposes only, no endorsement implied.

(none currently listed)

Tests

Procedure

  1. Measure the relative luminance of each letter (unless they are all uniform) using the formula:

    • L = 0.2126 * R + 0.7152 * G + 0.0722 * B where R, G and B are defined as:

      • if RsRGB <= 0.03928 then R = RsRGB/12.92 else R = ((RsRGB+0.055)/1.055) ^ 2.4

      • if GsRGB <= 0.03928 then G = GsRGB/12.92 else G = ((GsRGB+0.055)/1.055) ^ 2.4

      • if BsRGB <= 0.03928 then B = BsRGB/12.92 else B = ((BsRGB+0.055)/1.055) ^ 2.4

      and RsRGB, GsRGB, and BsRGB are defined as:

      • RsRGB = R8bit/255

      • GsRGB = G8bit/255

      • BsRGB = B8bit/255

      The "^" character is the exponentiation operator.

    Note: For aliased letters, use the relative luminance value found two pixels in from the edge of the letter.

  2. Measure the relative luminance of the background pixels immediately next to the letter using same formula.

  3. Calculate the contrast ratio using the following formula.

    • (L1 + 0.05) / (L2 + 0.05), where

  4. Check that the contrast ratio is equal to or greater than 4.5:1

Expected Results